泰州市兴化第三水厂初步设计(8万吨/日)毕业论文

 2021-04-12 10:04

摘 要

本设计为泰州市兴化第三水厂初步设计,工程设计规模为80000m3/d。设计的主要内容有设计水量的确定、工艺流程的确定和各净水构筑物的形式、选型及设计计算,再根据平面布置的原则,综合考虑各方面因素进行给水厂的平面及高程布置,最后绘制各主要构筑物工艺设计图。

净水厂的设计包括净水厂的位置选择、水处理工艺流程的确定、处理构筑物的设计计算以及水厂的平面和高程布置。确定净水厂的工艺流程选用方案:

原水—→静态混合器—→机械絮凝池—→斜管沉淀池—→普通快滤池—→消毒—→清水池—→二级泵站—→城市管网

采用管式静态混合器2个,设3个混合单元。机械絮凝池絮凝时间为21min,絮凝池分为三格,每格尺寸3.8m×3.8m,水深取为3.8m,共四组。斜管沉淀池尺寸:20m×9.5m,总高度:4.7m,水头损失为:0.15m,斜管中沉淀时间:4.9min。采用普通快滤池。水处理混凝剂选用聚合氯化铝([Al2(OH)nCl6-n]m)(15%),消毒剂选用液氯,每日用量为88.34kg。

关键词:给水厂;工艺设计;设计图;工艺流程

Preliminary design of Taizhou Xinghua third water plant (80000t/d)

ABSTRACT

The design is water supply project for XINGHUA city with the total volume of 80 thousand cubic meters.

The design is on the process of A water treatment plant. It is the size of 80000.The key elements of design including design to determine water content, technology process, and the form type calculation of each of water structures. Then according to the principles of layout taking various factors to the water plant layout of the plane and elevation Last draw water plant general layout, elevation charts and process design the main structures.

The design of water purification project contains of the selection of water treatment factory address, water treatment process of identification, handling the design of structures and the calculation of the plane and elevation water plant layout.

According to compare to both technologically and economically. And the programmer is preferred. The whole process is as follows: raw water→Static mixer→Machinery flocculation pond→settling tank→high speed filter cell→disinfection(add chlorine) →second pump station→ municipal pipe network.

Tubular static mixer with 2, set 3 mixing unit. Mechanical flocculation flocculation time of 21min, flocculation tank is divided into three cells, each cell size of 3.8m × 3.8m, water depth is taken as 3.8m, a total of four groups. Sedimentation pool size: 20m × 9.5m, total height: 4.7m, head loss is: 0.15m, inclined tube settling time: 4.9min. Using ordinary rapid filter. Use water treatment coagulants PAC ([Al2 (OH) nCl6-n] m) (15%), liquid chlorine disinfectant used, the daily dosage was 88.34kg.

Key words: water treatment plant;process design; design drawing ; technology circuit

目 录

1 设计任务及要求 ……………………………………………………………………………………… 1

    1. 设计任务及工作要求 …………………………………………………………………………… 1
      1. 设计题目 …………………………………………………………………………………… 1
      2. 设计进出水水质 …………………………………………………………………………… 1
      3. 城县人口及用水情况 ……………………………………………………………………… 1
      4. 气候条件 …………………………………………………………………………………… 1
    2. 设计工作内容 …………………………………………………………………………………… 1
      1. 设计内容 …………………………………………………………………………………… 1
      2. 设计要求 …………………………………………………………………………………… 2
  1. 总体设计 ……………………………………………………………………………………………… 3
    1. 城镇给水系统处理工艺流程的确定 …………………………………………………………… 3
      1. 净水工艺的要求 …………………………………………………………………………… 3
      2. 一般水源净水工艺流程选择参考 ………………………………………………………… 3
      3. 水处理工艺选择 …………………………………………………………………………… 4
  2. 城镇给水管网设计 …………………………………………………………………………………… 9
    1. 给水管网的布置 ………………………………………………………………………………… 9
      1. 给水管网定线原则 ………………………………………………………………………… 9
      2. 输水管区定线要求 ………………………………………………………………………… 9
    2. 给水管网的基本设计计算 ……………………………………………………………………… 10

3.2.1 各项用水量计算 ……………………………………………………………………………10

    1. 二级泵站设计参数的确定 ……………………………………………………………………… 11
      1. 流量计算 ……………………………………………………………………………………11
      2. 扬程计算 ……………………………………………………………………………………12
      3. 选泵 …………………………………………………………………………………………12
      4. 二级泵房的布置 ……………………………………………………………………………13
      5. 吸水井的设计 ………………………………………………………………………………14
      6. 起重设备选择 ………………………………………………………………………………14
      7. 泵房高度计算 ………………………………………………………………………………14
      8. 管道计算 ……………………………………………………………………………………15
      9. 通风与抽水设备计算 ………………………………………………………………………15
  1. 城镇给水处理厂设计 …………………………………………………………………………………17
    1. 药剂投配设备设计 ……………………………………………………………………………… 17
      1. 混凝剂药剂的选用 …………………………………………………………………………17
      2. 混凝剂的投加 ………………………………………………………………………………18
      3. 加药间设计计算 ……………………………………………………………………………18
      4. 静态混合器的设计计算 ……………………………………………………………………21
    2. 絮凝设施的设计 ………………………………………………………………………………… 23
      1. 设计水量 ……………………………………………………………………………………23
      2. 垂直轴式絮凝池计算 ………………………………………………………………………23
    3. 沉淀设施的设计 ………………………………………………………………………………… 28
      1. 设计流量 ……………………………………………………………………………………28
      2. 平面尺寸设计 ………………………………………………………………………………28
      3. 进出水系统 …………………………………………………………………………………29
    4. 普通快滤池的设计 ……………………………………………………………………………… 33
      1. 平面尺寸设计 ………………………………………………………………………………33
      2. 滤池高度 ……………………………………………………………………………………34
      3. 配水系统 ……………………………………………………………………………………34
      4. 洗砂排水槽 …………………………………………………………………………………39
      5. 滤池反冲洗 …………………………………………………………………………………42
      6. 进出水系统 …………………………………………………………………………………44
    5. 消毒设计 ………………………………………………………………………………………… 44
      1. 加氯量计算 …………………………………………………………………………………44
      2. 加氯设备的选择 ……………………………………………………………………………45
      3. 加氯间和氯库 ………………………………………………………………………………45
    6. 清水池的设计 …………………………………………………………………………………… 46
      1. 清水池的容积 ………………………………………………………………………………46
      2. 管道系统 ……………………………………………………………………………………47
      3. 清水池的布置 ………………………………………………………………………………48
    7. 离心式脱水机的设计 …………………………………………………………………………… 49
    8. 水厂的总体布置 ………………………………………………………………………………… 50
      1. 水厂的平面布置 ……………………………………………………………………………50
      2. 工艺流程的布置 ……………………………………………………………………………51
      3. 水厂的高程布置 ……………………………………………………………………………52
      4. 厂区管线 ……………………………………………………………………………………52
      5. 道路的布置 …………………………………………………………………………………53
      6. 环境美化 ……………………………………………………………………………………53

结论 …………………………………………………………………………………………………………54

致谢 …………………………………………………………………………………………………………55

参考文献 ……………………………………………………………………………………………………56

附录 …………………………………………………………………………………………………………57

您需要先支付 80元 才能查看全部内容!立即支付

课题毕业论文、开题报告、任务书、外文翻译、程序设计、图纸设计等资料可联系客服协助查找,优先添加企业微信。