景德镇市污水处理厂工艺设计毕业论文

 2021-04-12 11:04

摘 要

本设计是景德镇市污水处理厂污水处理工艺设计。设计规模为:近期30000/d。设计要求处理水排放到Ⅲ类水体,即达到《城镇污水处理厂污染物排放标准》GB18918-2002的一级B标准。要求根据所给资料进行设计的主要内容有:估算处理厂应处理的程度;污水处理工艺流程的选择,进行技术分析;主要构筑物的设计计算(附计算草图);污水厂平面布置;污水厂高程布置。根据出水要求,采用具有脱氮除磷效果的污水处理工艺--CASS工艺。污水首先经过中格栅的初步处理,再经提升泵房提升至相应高度经细格栅的处理后进入沉砂池,由沉砂池进入CASS池,在CASS池中完成曝气和沉淀,经混合器后进入接触池进行消毒并最终达到标准排出水体。污泥在经过CASS池的沉淀后自流入集泥井,再由污泥提升泵房提升至污泥浓缩池,经浓缩后流入贮泥池,最后经由污泥脱水间脱水成泥饼后运走。

CASS工艺相较于传统SBR工艺的间断进水,间断排水,CASS工艺可连续进水,克服了SBR工艺的不足,比较适合实际排水的特点,拓宽了SBR工艺的设计应用领域。虽然CASS时均考虑为连续进水,但在实际运行中即使有间断进水,也不影响处理系统的运行。溶解氧周期性变化,浓度梯度高,工艺流程简单,占地面积小,投资较低。

关键词 :城市污水;污水处理;CASS工艺

Abstract

This design is also the sewage treatment plant sewage treatment process design. Design of size: 30000 / d soon. Water in Ⅲ class water dealing with the design requirements, namely the reach the town sewage treatment plant pollutant discharge standard "level 1 B GB18918-2002 standard. Requirements according to the information given to carry on the design of the main contents are: estimate the extent of the treatment plant should be processed; Sewage treatment process selection, technical analysis; The calculation in the design of main structures (calculation sketch attached); Sewage plant layout; Sewage factory elevation layout. According to water requirements, using a nitrogen phosphorus removal effect of the sewage treatment process, CASS process. Sewage after the first grating preliminary processing, then through ascension pump up to the corresponding height after fine grille treatment into the grit chamber, the grit chamber into the CASS ponds, aeration and sedimentation in the CASS pool, pool disinfection after mixer into contact and ultimately to achieve standard discharge water. Sludge after the precipitation of CASS pool since into the mud collecting Wells, again by the sludge pump room up to the sludge concentration pool, after concentrated into the mud pools, finally through the sludge dewatering into mud cake off after dehydration.

CASS process than traditional SBR process of discontinuous water, intermittent drainage, CASS process can straight into the water, to overcome the disadvantages of SBR process, and is suitable for the actual drainage characteristics, broadening the application fields of SBR process design. Although CASS are consider as straight into the water, but in the actual operation even with intermittent water, does not affect the operation of processing system. Cyclical change, dissolved oxygen concentration gradient is high, the technological process is simple, cover an area of an area small, investment is low.

Keywords: urban sewage water treatment,CASS technology,sewage water treatment technology.

目 录

1 设计任务和资料 1

1.1设计任务 1

1.2设计目的 1

1.3设计意义 1

1.4设计要求 1

1.5设计资料 2

1.5.1项目概况 2

1.5.2设计依据 3

2设计方案论证 4

2.1 污水处理工艺流程比较及选择 4

2.1.1 工艺方案分析 4

2.1.2 目前常用的城市污水处理技术 4

2.2设计污水水量 6

2.3污水处理程度计算 7

3 污水处理构筑物设计 9

3.1各污水处理构筑物设计内容及主要设计参数 9

3.2各污水处理构筑物设计计算结果 10

4 污水构筑物设计计算 12

4.1格栅 12

4.1.1格栅的设计参数 12

4.1.2粗格栅设计计算 12

4.2污水提升泵房 13

4.2.1泵站设计的设计参数 13

4.2.2泵房形式及工艺布置 14

4.2.3泵房设计计算 14

4.3 泵后细格栅 15

4.3.1 设计参数 15

4.4沉砂池 17

4.4.1设计参数 18

4.4.2沉砂池的设计计算 18

4.5 CASS反应池 20

4.6 消毒设施 27

4.6.1 设计依据 27

4.6.2 设计参数 27

4.6.3 设计计算 28

4.7 污泥处理构筑物的设计计算 29

4.7.1 污泥泵房 29

4.7.2 污泥浓缩池 30

4.7.3 贮泥池 33

4.7.4 污泥脱水间 33

5 污水处理厂的布置 37

5.1污水处理厂平面布置 37

5.1.1平面布置原则 37

5.1.2平面布置 39

5.1.3 估算占地面积 40

5.1.4 污水处理厂附属建筑及其尺寸 40

5.2污水处理厂高程布置 41

5.2.1高程布置原则 41

5.2.2污水污泥处理系统高程布置 42

总结 44

参考文献 44

致 谢 45

附录 47

1 设计任务和资料

1.1设计任务

景德镇市污水处理厂处理工艺设计。

1.2设计目的

随着我国社会经济的迅速发展和人民生活水平的不断提高,用水紧张和污水排放的问题已越来越突出。由于我国城镇大部分的生活污水没有进行治理直接排放,加重了对环境的污染。因此对污水进行彻底的治理以保护人类赖以生存的环境的重要性也越来越大,高效节能的城市污水处理技术与工艺已能为国民经济的发展起到较大的推动作用,所以,提出一套合理、经济、运转效率高的工艺流程对污水进行处理,以达到标准排放,对于保护环境,减轻环境污染,遏制生态恶化趋势,有着重要的意义。

随着景德镇市经济的快速增长,污水的排放量也逐年增加,严重影响着市区周边的生态环境和可持续发展,为了实现和谐发展,必须严格进行污水处理,新建污水处理厂工程势在必行。

1.3设计意义

我国城市污水处理与其他国外发达国家相比起步较晚。近几百年来,城市污水处理已从原始的自然处理、简单的一级处理发展到利用各种先进技术、深度处理并回用。处理工艺也从传统活性污泥法、氧化沟工艺发展到A/O、A2/O、AB、CASS等多种工艺,以达到不同的出水水质要求。尽管如此,我国的污水处理还是落后于许多国家。在我们大力引进国外先进技术、经验和设备的同时,必须结合我国发展,尤其是当地实际情况,探索适合我国实际的城市污水处理系统。

其次,做本设计可以在很大程度上锻炼自己各方面的能力,包括理论分析、制定设计方案的能力;设计、计算、绘图的能力;技术经济分析和组织工作的能力;总结,撰写设计说明书的能力等。

1.4设计要求

(1)污水厂的设计和其他工程设计一样,应符合适用的要求,首先必须确保污水厂处理后污水达到排放要求。考虑现实的经济和技术条件,以及当地的具体情况(如施工条件)。在可能的基础上,选择的处理工艺流程、构(建)筑物形式、主要设备设计标准和数据等。

您需要先支付 80元 才能查看全部内容!立即支付

课题毕业论文、开题报告、任务书、外文翻译、程序设计、图纸设计等资料可联系客服协助查找,优先添加企业微信。